![]()
This image represents a finished sample approximately 600mm wide. The appearance of the veneer your screen, on a sample and that used in a project may differ from each other, because wood is a natural product and may vary in appearance from log to log and within a log. Veneer may have natural features such as pin knots, gum, figure, mild-indentations, slanted/curved direction of grain, paling-fence-effect, different leaf widths, off-centred crowns etc., and manufacturing features such as join lines and knife-rub-marks. These are not defects but intrinsic features of natural wood veneer and its processing.
Silky Walnut (Quarter-cut)
Species: |
Silky Walnut |
Cut: |
Quarter-cut
Crown-cut generally not available |
Matching: |
Book-matched
This veneer is normally Book-matched. For large areas of veneer such as walls and ceilings, and for projects to be nested and sawn/C&C routed, it is best to specify this species as Random-matched Colour-blended. |
| About this Product: |
This product is part of a special range of unusual natural wood veneers that includes striped, fiddle-back, quilted, burl and other less common veneers and species. Suitable for low-wear and dry vertical interior applications where character and uniqueness are required. The appearance of this veneer may vary because wood is a natural product. It may have natural features such as pin knots and figure. |
| How to Specify: |
Download |
| Nominal veneer leaf size(s): |
Length generally 2500mm. Widths - various. |
| Typical Finished Panel size(s): |
2400mmx1200mm |
| Thickness of Veneer: |
0.55mm - 0.65mm |
| Product Data Sheet: |
Download
|
| Availability: |
Reasonable availability |
| Price zone: |
Slightly above average |
| Applications: |
Suitable for interior, dry, low/medium-wear applications, vertical and low/medium-wear horizontal applications such as wall panelling, interior doors, furniture, ceiling panels, table- and desk-tops. It should not be used for high wear areas such as floors, stair treads, counter-tops exposed to heavy wear/water and kitchen counter-tops. Not suitable for use in high humidity, wet, steamy or damp conditions such as vanity tops, splash-backs or above stoves and dishwashers. Do not use in exterior applications, areas exposed to temperatures above 60 degrees C nor areas around stoves and fireplaces. Note that the appearance of veneer will change over time due to direct and indirect light, and exposure to heat and air. Some logs or leaves of veneer may age differently to other logs/leaves of the same species. Keep out of direct sunlight. As it is not possible to cover all associated manufacturing materials, conditions, products and methods, the end-user is responsible for carrying out the necessary tests and trials to check that the veneer, coating type, fabrication methods, associated materials and cleaning products/methods are suitable for the application. |
| About & Applications information: |
Download
|
| Colour/Appearance: |
Striped/Multi-coloured
|
| Consistency of Appearance: |
Average |
| Botanical Name: |
Dillenia species |
| Origin: |
New Guinea |
| Handling and Care instructions |
Download
|
| Edging availability: |
Veneer edging can be made by/is available from edge-band manufacturers. Note that edging may not necessarily look the same as the face veneer. Solid wood is generally not available. |
| Finish: |
Use a high quality low-yellowing 2-pack polyurethane designed for use with wood veneer for sealer and top coats, with manufacturer approved UV prohibitors. Sealer and coating film thickness to be as recommended by the coating manufacturer. Note that if wood stains are used, this may accentuate features such as pin-knots, figure, grain and join lines. Test pieces should be prepared to ensure that the coating and stains are suitable. |
| Pressing, Finishing & Fabrication information |
Download
|
| Environmental: |
Non-endangered |
| Environment Health & Safety information |
Download
|
| Available as environmentally certified: |
No
|
| Emissions from raw veneer: |
Zero Formaldehyde emissions (E0) and zero VOC's from raw veneer. To maintain E0 rating, specify E0 substrate and glue, and E0 water based low-VOC coating clear coat. |
| Formaldehyde statement |
Download
|
| Material Safety Data Sheet |
Download
|
IMPORTANT NOTICE - Briggs Fire Certificate(s)/Report(s) do not apply to FRMDF/veneers/laminates from other suppliers. They apply only to Briggs Veneers' Flameblock FRMDF/veneers/laminates/thicknesses as listed on our Fire Certificate(s)/Report(s). It is the responsibility of the end user to ensure that the products used on their project are as named on these Fire Certificate(s)/Report(s). Briggs Veneers does not accept any responsibility for product substitution by others. Do not publish Briggs Fire Certificate(s)/Report(s) on any website or in product literature as they are the property of Warrington Fire and/or Briggs Veneers. Flameblock is designed and tested to meet the National Construction Code 2019 (NCC 2019) Volume 1, Specification C1.10 Section 4 for interior walls, ceilings and lift car interiors. Flameblock is not rated for use in other areas of buildings that may require fire-retardancy such as doors, around fireplaces, etc. Nor is it rated as “non-combustible”. Panels which have been modified such as with acoustic slotting or multilayered Flameblock are not covered. Briggs Veneers are not qualified to advise what Fire Hazard Group Numbers are required for your application - please seek the advice of a Fire Engineer Consultant or Building Certifier.