Come and see us at Equinox Evolution Sydney on Thursday 19th September 2019 from 4:00 to 9:00pm at "The Venue", 55 Doody Street, Alexandria And Perth Equinox on Thursday, 10th October from 6:00 to 8:30pm at The Westin Perth, Grand Ballroom

loading...

This image represents a sample approximately 600mm wide. Colours displayed on your screen may differ from those of the actual sample. This laminate is made from natural wood so its appearance may vary and have natural features.

Oberflex Spice Pepper

Product:

Oberflex Spice Pepper

About this Product: Cannot be post-formed, but can be cold bent perpendicular to the grain, to a radius of approximately 300mm
How to Specify: Download
Laminate sheet size(s): 2500mmx1250mm (and 3050mmx1250mm by indent)
Typical Finished Panel size(s): 2400mmx1200mm
Thickness of laminate: 1.1mm
Product Data Sheet: Download
Availability: Good availability
Price zone: Considerably above average
Applications: Exceptionally good for high wear areas where stain resistance is required - such as reception counters, or tables used for food and drink. Not for exterior or wet areas, or floors. Keep out of direct sunlight.
About & Applications information: Download
Colour/Appearance: Patterned
- Natural variation in colour can occur between different logs and batches.
Consistency of Appearance: Better than average
Made from: Resin impregnated Walnut veneer, with a striped & stained surface - finished with a hard melamine surface and bonded onto a laminate backer
Handling and Care instructions Download
Edging & solid timber availability: Self-edge with same laminate. The side of the edge-strips must be sealed with a lacquer pen or similar.
Finish: Prefinished - Matt. Wire-brushed texture
Pressing, Finishing & Fabrication information Download
Environmental: Sustainably managed, non-endangered
Environment Health & Safety information Download
Available as environmentally certified: No
Emissions from laminate: : Formaldehyde - Less than 0.13 mg/m3 Formaldehyde = E1
Formaldehyde certificate Download
VOC emissions certificate: Download
Material Safety Data Sheet Download

FLAMEBLOCK is designed for use where Fire Hazard Group 2 fire retardant raw and veneered MDF (FRMDF) is required for interior walls and ceilings, as required by the National Construction Code (NCC) of Australia 2019. Black moisture resistant MDF is used where black substrate and panels are required for aesthetic reasons. All FLAMEBLOCK and Briggs Black MRMDF is PEFC™ certified for sustainability.

Assessment Report 23754.05 Section 5.4 shows that Briggs veneers of densities up to 755kg/m3 on 12mm+ Flameblock FRMDFare Fire Hazard Group 2.These veneers includeAmerican Walnut, White Oak, European Oak, Red Oak, Cherry, Rock Maple, Tasmanian Oak, Victorian Ash, Plantation Oak, White Ash, Hoop Pine, White Sycamore, Birch, Blackwood, Smoked Oak, Smoked Eucalypt, all the TrueGrainreconstituted veneers made from dyed veneer, the lower density TrueGrain Naturalveneers, and nearly all Woodstockand ecolignadyed veneers. This assessment was done according to AS 5637 using ISO 9705 Room Burn Tests, as required under the new National Construction Code 2019.

High density veneers such as Blackbutt, Spotted Gum, Ironbark, Jarrah, Marri, Stringybark, Sydney Blue Gum, Tallow-wood etc are not covered in this Report and so at this stage are only Group 3 on MDF or Flameblock FRMDF. Veneer laminates such as Oberflex, Innato and Shinnoki are not yet covered.

Raw Flameblock is Group 2 and veneer on Standard MDF is Fire Hazard Group 3

Fire Hazard Group Numbers in these Reports only apply to flat, un-slotted, non-routed panels. Note that we are not qualified to advise what Fire Hazard Group Numbers are required for your application - please seek the advice of a Fire Engineer Consultant or Building Certifier. Please do not put these reports on any website as they are the property of Warrington Fire. It is the responsibility of the user of all Briggs fire information, Fire Test and Assessment Reports to ensure that the products that they are applying this information to, are as described/named in the Reports. Briggs Veneers accepts no responsibility if our products are substituted.

Please contact us for New Zealand Group Numbers.

This/these fire certificate(s) apply only for the MDF, species, veneers, laminates and thicknesses as listed on the certificates. Please confirm with your fire consultant that these certificates meet the relevant BCA requirements for your application (interior walls and ceilings Class 2 to 9 Buildings).